|
HR10-250
TiVo Bracket
|
|
|
This is what you get in the TiVo Mounting Bracket Kit:
(1) Mounting Plate
(1) Linkage Arm
(4) Blue Rubber Grommets
(4) Metal standoffs
(5) Machine Screws 1/2" long with Lock-Washers
(6) Machine Screws 1/4" long with Lock-Washers
(4) Plastic Washers 1/16" thick
(1) #6 Lock Nut
(3) #6 Flat Washers
(3) C-Clips
(1) Plastic hex internally threaded spacer (not used)
|
Caution: The power supply is not enclosed and can shock
you if touched. Do not touch it, unless of course, you
want to be shocked!
This is a picture of the bottom of a HR10-250. You will be
putting a #6 x 1/4" long screw thru the hole that is circled
in red.
Place a C-Clip under the motherboard under the hole that is
between the power
supply and the existing hard drive. Tighten the #6 x 1/4"
long screw from the bottom of the TiVo into the C-Clip.
Note that the C-Clip does NOT sit on the motherboard but rather
on the bottom of the Tivo case.
Next we will be putting standoffs on the side of the TiVo.
The two red circles above show where the standoffs will be
positioned. Counting from the front of the TiVo, you will
put a standoff in holes 3 and 12 on the outside row of square
holes.
Put a #6 x 1/4" long screw with a washer thru the #3 and
#12 outside holes from the bottom of the TiVo and
tighten the screws into the C-Clip in each position.
Position the C-Clips as shown.
Press the plastic clip that holds the two cables together over
to the left. It may help to first untwist the
clip, push it over and then twist it back closed.
Next, install the linkage arm to the mounting plate. Put a #6
x 1/2" long screw first thru the mounting plate and then thru the
Round Hole in the linkage arm. The linkage arm goes
under the mounting plate. The linkage arm is attached
to either of the small holes that are closer to the larger
holes.
Thread a #6 Locknut on the #6 x 1/2" long screw and tighten with a wrench.
Position the linkage as shown. This screw should be snug.
Lay the assembled Mounting Plate with Linkage Arm on the C-Clips to make sure that the
holes in the C-Clips on the edge of the TiVo line up with the holes in the
Mounting Plate. If they do not, you can loosen the C-Clips
from the bottom and slide them around until everything lines up.
Make sure to tighten the C-Clips if you loosen
them. Adjust the Linkage Arm attached to the Mounting
Plate so the hole in the Linkage Arm lines up with the hole in
the C-Clip that is mounted near the middle of the TiVo next to
the power supply. Don't touch the power supply!
Next, install the Blue Grommets in the Mounting Plate. A small
screwdriver can be of help. Then position the Mounting Plate over
the hard drive as shown, lining up the Grommets with the screw
holes in the hard drive. Note that the IDE and power
connections on the hard drive above are to the left.
Line up the center of the Grommets with the screw holes in the
hard drive. Then put a Metal Spacer in each of the
Grommets. Next put a Plastic Washer over a #6 x 1/2"
Screw
and screw into the hard drive in each of the Blue Grommets.
Snug up all Screws.
Now for final assembly! Press the two cables down, moving
the plastic clip that holds them together to the side.
Line up the two holes in the C-Clips that you installed at the
edge of the TiVo and secure with two #6 x 1/4" long Screws.
Insert a #6 x 1/4" long Screw in the hole in the Linkage
Arm near the power supply.
Snug up all of the Screws.
And the installed hard drive will look like this
Note: You may find that you have a
couple extra screws or other parts left over. Don't worry,
this is normal. We use the same hardware kit for other
brackets that mount differently.
|
